Bearings, Shafts, & Spacers

The Vortex Shaft - MAXSwerve Integrated Key is compatible with the REV ION System and gives users the ability to drive a MAXSwerve Module without the need for the MAXSwerve Key. This eliminates a potential point of failure in the MAXSwerve since the key...

The Vortex Shaft - 20DP Gear - 7T is compatible with the REV ION System and offers users the unique ability to achieve substantial gear reductions directly from the motor. This gear features a 7T 20DP design that is typically too small for an 8mm keyed...

The Vortex Shaft - Falcon Compatible Spline is compatible with the REV ION System and gives users the ability to drive components that have a falcon spline bore. *Falcon is not a REV trademark. Featuring a 1/2in hex section that drives the shaft and a...

The 8mm Vortex Shaft, compatible with the REV ION System, empowers you to utilize the NEO Vortex Brushless Motor with any 8mm keyed shaft component. This interchangeability also means that the NEO Vortex matches the output of a NEO Brushless Motor V1.1,...

The Vortex MAXPlanetary Input Kit is compatible with the REV ION System and gives users the ability to mount a MAXPlanetary Gearbox directly to your NEO Vortex Brushless Motor and SPARK Flex Motor Controller. Working seamlessly with the MAXPlanetary...

The MAXSpline Shaft is compatible with the REV ION System. The shaft is an extruded aluminum MAXSpline that provides a high strength alternative to 1/2in hex shaft that can interface with any REV ION System components with a MAXSpline bore. The...

MAXSpline Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. The MAXSpline Spacer with MAX Pattern features a 2in bolt circle pattern...

MAXSpline Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. Specifications Material: POM (Acetal/Delrin) OD: 1.50in Weights &...

#10-32 Standoffs are compatible with the REV ION System and provide spacing for mounting key items on your robot. These standoffs are tapped on each end for a #10-32 thread and have a 3/8in flat to flat dimension, similar to a #10-32 nut...

#10 Spacers are compatible with the REV ION System and are an accurate way to space structural components like plates, brackets, or tubes apart on #10 screws. Can also be used to to space motion components like gearboxes away from their mounting...

1/2in Rounded Hex Shafts are compatible with the REV ION System and are a ready-to-use length of hex shaft that have been cut to length and have the ends tapped. The ends are tapped #10-32 in order to accept a screw and washer or shaft collar. The 1/2in...

1/2in Hex Shaft Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. Specifications Material: POM (Acetal/Delrin) OD: 0.72in Weights &...

Dead Axle Tube is compatible with the REV ION System and can be used with 3/4in Needle Bearing Carrier (REV-21-2385) and MAXSpline Shaft (REV-21-2520) as the dead axle in a dead axle roller. Can also be used with custom rollers and as...

The Stepped Bushing - 3/4in ID is compatible with the REV ION System. This bushing used in conjunction with the MAXSpline Shaft and Dead Axle Tube - 3/4in can be used to build robust and effective rollers and intakes...

Commonly included with our gearboxes and pinion options, the 8mm Keyed Shaft Retaining Hardware Pack is compatible with the REV ION System and includes the hardware needed to retain 2mm keyed elements to 8mm OD shafts without the bulk of alternative...

The ION Motor Mounting Blocks family offers two options for securely mounting motors and supporting extended shafts within robot mechanisms. Both versions use aluminum plates with integrated MAXSpline bores and bearing pockets, providing a consistent...

The 8mm Shaft Spacer is a stainless steel 1/16 inch washer designed for precise shaft spacing in FRC and FTC mechanisms. Used on the NEO 2.0 Brushless Motor to achieve correct input coupler alignment in MAXPlanetary assemblies, this spacer also fits any...

MAXSpline Shaft Collars provide mechanical retention for components mounted on MAXSpline Shaft and use a two piece aluminum clamping design for secure attachment. Both versions are black anodized for durability and integrate cleanly within the REV ION...

The MAXSpline Shaft - Polycarbonate brings the versatility of the MAXSpline profile to lightweight mechanisms where reducing mass is a priority. Designed for intakes, conveyors, and other low load assemblies, this shaft provides an easy way to build...

The Locking MAXHub - 1/2in Hex Kit is a compact, dual plate hub system designed to secure 1/2in hex shafting inside any MAXSpline bore component. Each kit includes two identical wedge locking plates and the necessary #10-32 hardware. When the plates are...