Electronics

The Digital LED Indicator is a LED signal module that is digitally controlled (active low) and offers three colors: red, green, and amber. The Digital LED Indicator is designed to directly interface with the DIO ports of the Expansion Hub or Control Hub...

Touch sensor is best used for user input, but can also be used as a limit switch.  Configuration The REV Touch Sensor is a digital sensor that is wired to the N+1 channel on our standard 4-pin JST PH connector. In other words, the REV Expansion Hub...

The 36in CAN Extension Cable is a 3-pin connector to interface with existing CAN devices.  Specifications Length: 36in (3ft) Wire Colors: yellow, green 22 AWG

This JST-PH 6-pin Breakout Board is designed to adapt external sensors to the SPARK MAX 6-pin Encoder Port standard. It features a JST PH 6-pin connector, labeled solder pads, and through-hole pads that are compatible with popular 63R style quadrature...

These plastic clips are designed to keep standard 0.1" 3-pin PWM connectors together. Simply clip them around an assembled pair of connectors.

The NEO 2.0 Sensor Cable connects the NEO 2.0 Brushless Motor’s sensor port to a standard JST PH 6-pin interface used on REV motor controllers. The 2x3-pin PHSD connector provides a secure, latching connection at the motor, while the 6-pin JST PH...

The CAN Terminator Pack provides two compact, plug-ready termination options for teams looking to maintain reliable CAN bus performance anywhere in their robot’s wiring. Each terminator uses a small 10mm x 10mm internal circuit board sealed with...

The MAXSpline Grommet provides a simple way to route wires through MAXTube while preventing abrasion against bare aluminum. Made from pliable 60A rubber, it press-fits into the MAXSpline Bore on MAXTube with a 1/8 inch wall, creating a clean pass-through...

The REV Through Bore Encoder V2 provides precise, reliable shaft position measurement with both incremental (ABI quadrature) and absolute (pulse-width) outputs. Its ½" hex through bore mounts easily within common FRC/FTC mechanisms, and the...

The SPARK MAX Data Port Breakout Board makes it easy to connect external sensors to the SPARK MAX Data Port. For additional information on the SPARK MAX Data Port, please take a look at the SPARK MAX User's Manual. Analog Input Issue - Affects Rev. A...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

The REV Servo Hub is compatible with both the REV ION and REV DUO systems. Over a single communication interface it can provide advanced control of up to six (6) servos. This means that the Servo Hub needs no additional PWM cabling between it and your...

Mounting your SPARK MAX Motor Controller (REV-11-2158) has never been easier with the help of the SPARK MAX Mounting Bracket. Configured with a hole pattern compatible with a 1/2in grid and allowing the mode and status light to be seen, this...

This update to the SPARK CAN Cable bridges the H and L CAN signals together within the cable itself. This prevents the CAN Bus breaking in the event of a cable disconnecting from a SPARK MAX Motor Controller. These SPARK CAN cables have a JST-PH 4-pin...

Now legal for both FTC and FRC! Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The Blinkin LED Driver is a compact LED driver module that simplifies controlling...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 90cm (35.5in) REV-11-3327: Length: 30cm (11.81in)

The WAGO 221 Inline Splicing Connector is a robust and easy to use splicing connector that makes fiddling with hard-to-master crimp-style connectors a thing of the past. Simply lift the lever up, insert the stripped wire, and push the lever back down to...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

The REV Robotics Smart Robot Servo (SRS) is a configurable metal-geared servo that takes the guesswork out of aligning and adjusting servo based mechanisms. One SRS can be used as a standard angular servo, a custom angular servo, and a continuous...