FTC Discounts

With an efficient right-angle configuration, the Ultra 90 Degree Gearbox offers a robust solution to building a more compact robot. The Ultra 90 Degree Gearbox allows you to connect the UltraPlanetary Gearbox and the HD Hex Motor (REV-41-1600)...

The U Channel Endcap spans between the two sides of U Channel to provide holes on multiple surfaces to fasten additional components to. Also, using the endcap is a great way to strengthen longer sections of U Channel that are experiencing high loads...

Make driving linear motion easy with the 22 Tooth Plastic Right Angle Rack Gear. Mount the rack gear to a slot in either the REV DUO Extrusion or REV DUO Channel while using any of the REV DUO Plastic Gears to drive motion. Specifications Module: 0...

Custom hinge system used to create compact, simple hinges using REV DUO 15mm Extrusion. Hinges come in left, right, and center pieces, and are attached together using standard M3 hardware. Specifications Hole Diameter: M3 clearance Hole Spacing:...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

Use the Anderson Power Pole to 2-pin JST VH Adapter Cable to connect your existing motors to the REV Robotics Expansion Hub. Teams that already own and use the Anderson Powerpole Crimper may purchase JST VH 2-pin Motor Cables (REV-31-1413), cut cables in...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

M3 Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts on a M3 bolt.  

M3 Ball Joint Rod Ends are compatible with the REV DUO System. The Female M3 Ball Joint Rod End (REV-49-1560) can either be paired with its male counterpart to create short linkage arms or with M3 threaded rod and a second female ball...

5mm Metal Hex Bore Gears are compatible with the REV DUO System and work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic...

5mm Plastic Hex Bore Gears are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Gears 45 tooth...

15mm Plastic Motion Brackets are compatible with the REV DUO System. Each bracket features a set of alignment ribs designed to seat the bracket into the extrusion channel increasing joint alignment, strength, and rigidity.  The 15mm Plastic...

DUO Flat Beams are compatible with the REV DUO System and are easy to use. Having an 8mm width, 3mm height, and 8mm hole pattern makes them perfect as a support for an upright or using them as a linkage.  Specifications Material: 6063...

This Motion Pattern Spacer offers a convenient and accurate way to space gears, sprockets, wheels, and other parts through the Motion Pattern interface. Great for getting the proper spacing when face mounting to the UltraPlanetary Gearbox...

This is all of the hardware included in the 15mm Linear Motion Kit V2 (REV-45-1507). Specifications Hole Diameter: M3 Clearance Kit Contents QTY 8 - M3 x 8mm Low Profile Socket Screws QTY 8 - M3 x 8mm Hex Cap Screws QTY 8 - M3 Nyloc Nuts QTY 8 - M3...

The JST PH 6-pin to JST PH 4-pin Cable allows for seamless connection of the Through Bore Encoder to the dedicated encoder ports on the FTC Control System (Expansion Hub or Control Hub). Also allows for the HD Hex Motor to...

These plastic 15mm Extrusion Slot Covers are ideal for making any machine look great!  COLOR  SKU  Red  REV-41-1633  White  REV-41-1634  Blue  REV-41-1635  Yellow  REV-41-1636  Green...

These set screws have a pre-applied coating of nylon, helping them to stay in place under vibration. Use these with REV's standard Shaft Collars or new Slim Shaft Collars to never lose another shaft collar in a match! Specifications Material: Steel